Changelog of DAMC-FMC1Z7IO MMC

V2.08

• Raise IPMI thresholds for DCDCs from 60, 70, 75 to 85, 95, 100 deg.C. Note that the raised thresholds can affect overall cooling of a crate, since the DAMC-FMC1Z7IO will now endure higher temperatures before issuing temperature events. Please check crate cooling and potential overheating of other system components after the DAMC-FMC1Z7IO has been upgraded.

V2.07

• Assert write protect on PMBUS PSM
• Update CPLD to v1.12
• Add interlock override

V2.06

• Fix RTM Vadj (single ended) value to 2500mV
• Provide RTM_Vadj (D-TACQ) as IPMI sensor

V2.05

• Prevent I2C MUX conflict on PL CPLD update
• Change default FRU to Zone3 Class D1.0

V2.04

• Fix support for in-app CPLD update on Rev.C

V2.03

• Add reg.dump, stack dump & backtrace on watchdog reset

V2.02

• Make MCH show_fru show product name from FRU
• Add support for board Rev.C

V2.01

• Fix manual fru_start/shutdown from MCH
• Fix rebooting with PP enabled

V2.00

• Migrate to new CPLD regmap
• Add FMC PG signals

V1.07

• Fix mmcterm
• Improve IPMI latency
• Fix CPLD error on reset
• Misc RTM fixes and improvements
• Add support for FRU FmcI2cDeviceDefinition
• Support RTM handle in out-of-crate mode
• Add RTM Isens calibration

V1.06

• Fix cps command

V1.05

• Skip Z3_DRV_EN when 12V not enabled

V1.04

• Fix FRU ID in RTM device locator
• Include Stamp UID in version info & boot msg
• Add support for detection of unprogrammed power manager
• Fix unintended M1->M4 transition in bootloader
• Make show_fru on MCH show the actual name of the RTM
• Improve IPMB debug logging

V1.03

• Fix HPM update of Z7 SPI flash

V1.02

• Fix 'qz' command

V1.01

• CPLD: Update to 6.0
• PMBUS: Update config; enable RTM_Vadj 3.3V setting
• Add cps command (support TCLKA/B multiplexing)
• Change default boot mode to QSPI
• Add 'qz' command to set QSPI chip selection
• FMC: Add support for 32k EEPROM at different address
• FMC: Add support for optional GA-swapped fallback EEPROM addresses
• CPLD: Fix errors when rebooting w/ 12V enabled
• Add eefd command to set EEPROM to factory defaults

V1.00

• Check for unprogrammed power manager
• Add support for jitter cleaner
• CPLD 5.2: Add PCIe disconnect on FPGA reconfig
• Add support for RTM_Vadj
• Don't access payload CPLD when PP not ready
• Add ppf command
• Fix fru parser for long part numbers
• Fix FPGA INIT & DONE sensors
• Fix wdg reset when i2cd operated on blocked bus

V0.18

• Add board revision detection
• Switch PMBUS config to Rev.B file; don't configure PMBUS in Rev.A
• Don't configure SI5341 for Rev.B or higher
• Fix PMBUS channel names for RevA; add channel names for RevB
• Add payload power fail policies (stop, retry, ignore)

V0.17

• Fix bootloop on FMC I2C error
• Add i2cget / i2cset commands

V0.16

• Add support for FMC sensors
• Upgrade CPLD (fix FPGA UART on USB)

V0.15

• Fix CPLD update

V0.14

• Upgrade to recent CPLD w/ EFB interface. Drop support for older / pre-EFB CPLDs

V0.13

• Add DRTM-PZT4 compatibility mode

V0.12

• Fix power management for Vadj=1.2V

V0.11

• Fix MCH warnings / fail LED / power cycle in bootloader mode

V0.10

• Fix redundant decimal places on NAT sensor display

V0.09

• Fix rounding errors in sensors coefficients
• Fix I_RTM sensors increments
• Force I_RTM readings to zero if RTM off

V0.08

• Add R/W support for FMC EEPROMs
• Add FMC EEPROM addr. width auto-detection
• Add support for out-of-crate mode

V0.07

• Update libdmmc; fix PLL startup/config issue

V0.06

• Fix "Z3 compatibility" FRU parsing
• Fix deadlock on Si534x config failure

V0.05

• FRU write verify, fix corrupt AMC FRU

V0.04

• Wait for shutdown complete, when handle is pulled. Keep 12V PP, until PSM has gracefully shut down.

V0.03

• Add CPLD in-application update over HPM

V0.02

• preliminary version w/ FMC & RTM e-keying

V0.01

• Fix FPGA boot sequence

V0.00

• initial